Introductionby the current inserts. For more
a
Congratulations! With The Bridgeyouinformation or updates, visit
are entering the new world of listeningThe Bridge section of our Web
enjoyment made possible by combin-site at www.harmankardon.com.
ing the incredible storage capacity andUse the following as a guide to
¨
playback flexibility of an iPod(notdetermine which insert is correct
included) with the sonic power of yourfor your iPod model:NOTE: Do not place an iPod in
Harman Kardon receiver.Y For any iPod with a color screen,The Bridge unless an insert is
With a single, simple connection, yourincluding all iPod photo models, useinstalled; otherwise, the iPod will be
iPod is connected, and from there allthe insert with OCOLOR/PHOTO� onprevented from properly connecting,
you need to do is use your remotethe back. This insert is alreadyand damage will be caused to The
control and you are ready to go!installed in The Bridge.Bridge or your iPod that is not covered
by the warranty for either product.
FeaturesY For 20GB or 30GB iPod photo
models only, remove the insertConnecting The Bridge to
Y Single connection to any The Bridge-
marked OCOLOR/PHOTO� andYour Receiver
ready Harman Kardon receiver
attach the two included foam padsBefore connecting The Bridge, turn
Y Plays audio from an iPod through
to the rear inside wall in the well ofyour receiver off using its Master
your Harman Kardon receiver
the insert before replacing it.Power Switch. You will know that
Y Controls your iPod using the
Y For iPods with a black and whitethe power is off when the front-panel
Harman Kardon remote
screen and a 10GB, 15GB or 20GBPower Indicator (normally amber
Y Easy track selection with on-screen
hard drive, use the insert withwhen the unit is in the Standby mode)
navigation
O10GB/15GB/20GB� on the back.goes out. Depending on your receiver
Y Charges the iPodmodel, the Master Power Switch is
Y For iPods with a black and white
located above the Power Indicator or
Selecting the Correct iPod Insertscreen and a 30GB or 40GB
behind the front-panel door.
Each iPod model is a slightly differenthard drive, use the insert with
With the receiver off, press the button
size, making it necessary to use anO30GB/40GB� on the back.
on each side of the connector at the
insert that matches your specific iPodY Use the insert with Omini� on the
end of The Bridge cable and insert this
to The Bridge. The Bridge is shippedback for all iPod mini models.
with the insert for the color screen andY Use the insert with OUniversal� onplug into The Bridge/DMP port on the
receiverOs rear panel. If the port is hor-
photo models already installed; if youthe back for iPod models that come
izontal, insert the connector with the
own one of those models, no furtherwith a special insert.
changes are needed.flat side up. If the port is vertical, insert
To remove the 30GB iPod photo
the connector with the flat side to the
If you own a different iPod, first selectinsert, or if you need to replace the
right. In all cases, the connector will
the insert that matches your model.insert at a later time when you change
only go in one way. If you inadvertently
The model identification is printed oniPod models, hold The Bridge with one
try to plug the connector in the wrong
the back of each of the four extrahand and grab the edges of the insert
way, do not force it. Simply reverse
inserts supplied with The Bridge. Notein The Bridge and pull straight up.
the connector and try again.
that the insert marked OUniversal�Once you have selected the correct
should not be used alone. It isinsert, place it over the well in the
designed for use with future iPodcenter of The Bridge and gently press
models that are not accommodatedit down so that it snaps into place.
2 |
ACEC
